Question: How To Measure Draw Length For Bow?

Compound Bow Fitment Guide

Compound bows are designed to draw back a certain distance and then stop, which is controlled by the bow’s mechanical systems. The mechanical setting of the bow and the physical size of the shooter must match. Most modern compounds require less than 20 lb. of pressure to hold back at full draw.
The longer your draw length, the longer your bow’s powerstroke will be. The AMO/ATA specs for measuring draw length refer to the actual bowstring at its nocking point.
A good rule of thumb is to select a draw weight that requires about 75% of your “maximum” strength. If your bow is too heavy to draw back, and you can only shoot a few times before becoming fatigued, you’ll be less likely to practice and improve your game. Industry standards require at least 5 grains of arrow mass per pound of draw weight.

What is draw length in archery?

Draw length is a measurement of how far you pull back the bow in inches. For compound-bow archers, a bow technician estimates your draw length based on your wingspan. Photo credit: Shane Indrebo. Draw length is a measurement of how far you pull back the bow in inches.

How long should my arrow be for a 27 inch draw?

The weight is suspended from the center of the arrow, which must be 29″ long and supported by two 28″ apart points.

How long should my arrows be for a 29 inch draw?

According to our experience, if you use a 29u2032u2032 draw with compound bows, the arrow length should be 27.5u2032u2032 (29u2032u2032 u2013 1.5u2032u2032). This allows the arrow to comfortably fit on the arrow rest, but make sure your riser measurement matches up before purchasing a large quantity of arrow.

We recommend reading:  Readers ask: How To Draw A Head Step By Step?

How do I know if my draw length is too long?

The draw length is probably too long if the bow arm drops or swings to the side. When this happens, the scapula has already pushed the bow arm out as far as it can extend before the arrow is released, leaving no room for the bow arm to go forward, so it drops or swings to the side.

What length arrows for 27.5 draw?

Yes, a 29″ arrow for a 27.5″ draw length seems excessive, but most modern rests sit well behind the riser, allowing you to shoot an arrow shorter than your DL.

How long should arrows be for a 28 inch draw?

Your arrow length should be around 27 inches if you have a 28-inch draw length and want an arrow that ends at the front of the riser, but it can be longer if you need to weaken the spine of your arrow. Arrows should not be cut too short for safety reasons.

What does 400 mean on an arrow?

The numbers refer to the stiffness of the arrow’s spine; a 400 spine arrow is for bows weighing 40-60 pounds, a 350 spine arrow is for bows weighing 55-75 pounds, and a 500 spine arrow is for bows weighing 30-50 pounds.

How long should my arrows be for a 30 inch draw?

When shooting fixed-blade broadheads, which tend to magnify tuning issues, the Easton spine chart recommends a spine of 250 for a 30-inch arrow shot from a 70-pound bow; cut that arrow length down to 28 inches, and the spine chart recommends a spine of 340.

We recommend reading:  Readers ask: How To Draw A Frog Step By Step Easy?

How do I measure my draw length?

To determine your draw length, stand with your back to a wall and stretch your arms out against the wall, measuring the distance between the tips of your middle fingers to the tips of your other middle fingers, or the length of both arms, hands, and chest. Subtract 15 from this measurement and divide by two to get your draw length.

How do I know if my draw length is short?

The draw length that allows you to anchor in a comfortable position with your bow arm elbow unlocked (slightly bent) and your release arm elbow and forearm pointing straight away from the target is ideal for you. If the release arm elbow points left or right, your draw length is too long or too short.

What happens if draw length is too long?

Shorter draw length affects your body position because our elbow has to bend to compensate for the shorter draw length. Longer draw length forces our bow arm to overextend when we shoot, which messes up our anchor point and degrades our accuracy.

Leave a Reply

Your email address will not be published. Required fields are marked *